Your Shopping Cart is empty!
Welcome to 
86-752-2203959
Description
PP Pleated Cartridge Filters are made of Polypropylene fiber media. PP pleated cartridge filters provide excellent filtration efficiency and chemical compatibility across a wide range of liquid filtration process applications.
The constitution of nominal PP pleated filter cartridges adopt thermal welding techniques to seal all components, so no side leakage and optimizing PP pleated cartridge 100% integrity. PP pleated filter cartridges have large surface area that allow for greater system flow rate and higher dirt holding capacity than depth filters. PP pleated cartridges are widely used in prefiltration field requiring high purity.
Feature
1. PP pleated cartridge filters are manufactured in clean room and high cleaning environment
2. PP pleated cartridges are low pressure drop, high capacity of impurities and long service life
3. Polypropylene pleated cartridges are strict election materials which according to FDA standard
4. Ulti-layers structure, good filtration efficiency and consistent of performance for broad application range
5.The components of PP pleated filters are assembled in fully sealed condition by thermal bond, free of binder
Applications
1. Etchants
2. Chemicals
3. Cosmetics
4. Oil industry
5. Semiconductor
6. Food & Beverage
7. Medicine Filtering
8. Paints and Coatings
9. Prefiltration for RO/DI
Specification
| Filter Media | Polypropylene |
| Length | 5", 9.75", 9.8", 10", 20", 30", 40" |
| Outside Diameter | 2.75"(70mm) |
| Filtration Rating | 0.1μm, 0.22μm, 0.45μm, 0.65μm, 0.8μm, 1μm, 2μm, 3μm, 5μm, 10μm, 20μm, 30μm, 40μm, 50μm, 60μm |
| Core | Polypropylene |
| Support/Drainage | Polypropylene |
| Gasket/O-ring | Silicone, EPDM, Viton, NBR, Teflon encapsulated Viton |
| End Cap/Cage | Polypropylene |
| End Cap Type | DOE, 222/Flat, 222/Fin, 226/Flat, 226/Fin, 215/Flat, 215/Fin |
Feature
● Polypropylene pleated cartridges are strict-election materials according to FDA standard
● PP pleated cartridges are with low pressure drop, high capacity of impurities and long service life
● PP pleated cartridge filters are manufactured in clean room, maintaning high cleaning environment
● Ulti-layer structure, good filtration efficiency and consistent performance for broad application range
● The components of PP pleated filters are assembled in fully sealed condition by thermal bond, free of binders
Application
| Cosmetics | Etchants | Oil industry |
| Chemicals | Food & Beverage | Medicine Filtering |
| Semiconductor | Prefiltration for RO/DI | Paints and Coatings |
Performance
Operation Data for PCF Series Nominal PP Pleated Cartridge Filters
| Maximum Operating Temperature | 80℃(176℉) |
| Max. Differential Pressure | 4.8 bar at 20℃ (70 psi at 68℉) |
| 3.4 bar at 50℃ (50 psi at 122℉) | |
| 1.4 bar at 80℃ (20 psi at 176℉) | |
| Maximum reverse pressure | 40 psid @ 70°F (2.8 bar @ 21°C) |
| Recommended Change Out Differential Pressure | 2.4 bar (35 psid) |
| Sterilization Temperature Time | 121˚C (250˚F) for 30 minutes at 1.0 bar (14 psi) |
Pressure Drop Rate for 10" PP Pleated Cartridge Filters
Tech Support
Electron Microscopic Photo of PP Membrane
| 3D Drawing for PP Pleated Cartridge Filters | ||||||||||
 | ● Thermal welding techniques ensure PP pleated filter cartridges no side leakage ● Ulti-layers pleated, low pressure drop, high capacity of impurities and long service life ● 100% integrity tested, ineer core and outside cage strengthen capacity of high flow pressure ● Large surface area that allow for high flow rate and higher dirt holding capacity than normal depth filters | |||||||||
| Installation Example for PP Pleated Cartridge Filters | ||||||||||
 | ● Manufactured in continuous lengths up to 40 inches and vrious of filtration ratings ● Wide range of chemical compatibility used in prefiltration fields with high flow rate ● Special PP pleated cartridge filters can be made, such as special length and S.S. inner core ● Various of end caps fit for standard filter housings, easy to install help to save some manpower and time | |||||||||
End Caps of PP Pleated Cartridge Filters
Oder Information
| PCF | Length | Micron Rating | End Cap | Gasket/O-ring | Adders |
| PCF Series Nominal PP Pleated Cartridge Filters | 5 = 5" | 0.1 = 0.1μm | A = Double Open End (DOE) | S = Silicone | K = Thicker PP Cage |
| 0.22 = 0.22μm | |||||
| 9.75 = 9.75" | 0.45 = 0.45μm | B = 222/Flat(SOE) | |||
| 0.65 = 0.65μm | E = EPDM | ||||
| 9.8 = 9.8" | 0.8 = 0.8μm | C = 222/Fin(SOE) | |||
| 1 = 1μm | I = Stainless Steel Insert End Cap | ||||
| 10 = 10" | 2 = 2μm | D = 226//Flat(SOE) | N = NBR | ||
| 3 = 3μm | |||||
| 20 = 20" | 5 = 5μm | F = 226/Fin(SOE) | |||
| 10 = 10μm | V = Viton | ||||
| 30 = 30" | 20 = 20μm | G = 215/Flat(SOE) | S = Stainless Steel Core | ||
| 30 = 30μm | |||||
| 40 =40" | 40 = 40μm | H = 215/Fin(SOE) | T = Teflon Encapsulated Viton | ||
| 50 = 50μm | |||||
| 60 = 60μm |
For Example:
PCF-10-1-B-S
PCF Series Nominal PP Pleated Cartridge Filters - 10" - 1μm - 222/Flat(SOE) - Silicone O-ring
English
